Archive for Diamonte yarn

Passap vs Brother Placemat by Tricia Shafer


DSCF3915

DSCF3920

I made this  Tricia Shafer plated place mat(top picture)  on the Brother years ago and I liked it. I decided to make it again. When I finished, I decided to try to duplicate it on the Passap. And that is when I found out I can’t. (Notice , I said “I can’t” , maybe someone else can) I also found out from a friend in Arizona that there is a plating attachment for the passap, though rare to find.

I made the placemat on the Brother with two strands of Estillo for both yarns . On the botton one made on the passap I used one strand of Diamonte. I tried two strands of Estillo to start and I think I had problems because I did not have the right tensions. Looking back now, I bet it would be the same size as the first one if I did use the 2 strands of estillo.

Here are the comparisons . The plated mat is heavier and had a great shape when it came off the machine.  The passap was made just using blue diamonte using the same amount of stitches . The passap mat is smaller by about one and a half inches but it still is a nice size. The passap mat is not as nice shaped and is much lighter. The pattern came out nice on both mats done on different machines. So, I have to give the vote to Brother just because I don’t have the plating attachment for the Passap. 😦

To make this on the passap, I cast on N/N 1/1  and knitted the two CX 2../2.. rows and the N/N 5/5 row and then I transferred stitches from the front bed to the back bed.

Below is the  set up on the front bed.(of course you will have more needles than the diagram) The ends have 2 needles in work . The dots are the needles out of work.The back bed has all of the needles in work and the racking handle is down while knitting. You will put it up when transferring the stitches so the needles line up at the beginning transfers.

I cast on 63-63 on front bed and one less on back bed so the end needles are on the front bed. After transferring the front bed stitches to the back bed,(if you have one left over double up the stitches so that both ends look like the diagram below) put those needles out of work and put pushers in work under the remaining needles in work. Set locks to LX/N. I set the back bed tension to 5 and the front bed tension to 3. On the Brother the tensions were 7 on the main bed and 3 on the ribber. The sequence is six rows of knitting at LX/N and then 2 rows of LX/GX so that only the front bed needles knit.ALSO:in her pattern , Tricia  only does two rows of knitting instead of six between the  rows , two times,and you can see that in the pattern. There are three lines close together dividing the mat in 3. There are 158 rows of knitting . To finish transfer the front bed stitches to the back bed and bind off the stitches.

11.1.111.1.1.1.1.1.111.1.1.1.1.1.111.1.11

 

Passap Queen of Diamonds by Irene Krieger


 

 

 

dscf3873

Well, between the doctor appointments for my husband and me, it is really cutting into my craft time! Haha

I am sorry it took so long to post the directions on how to do this but I knew it was going to take a long time to do it and I was right.It has taken me over 6 hours to write the instructions  so that I don’t confuse you AND to figure out how to knit it again. Then I had to knit it again, following my instructions to make sure I had all the numbered rows right and the needles that should be in work.Lol By knitting this over again I realized that I have a mistake in my previous posting but this one is perfect.It is true that the third time is the charm.

The instructions are in my drop box with four pictures to show you how your work should look on those rows. I hope they help.

I sure hope someone that follows my blog will give this a try to make me feel like my time was not wasted. 🙂 Well, I guess it wasn’t since I learned it. Tee Hee

https://www.dropbox.com/sh/qivgfn30788iuau/AADzYhHEg8mq3CfMmeoFD64ua?dl=0

Passap China Pattern Sweater


dscf2915

dscf2916-1

I just finished knitting this  sweater following a pattern  called China Pattern Jacket . It is in Modern Machine Knitting magazine dated June of 1992 . I made this on the Passap E6000 and made lots of modifications. I made it a sweater instead of a jacket. I used win/crea to change the patterns of the leaves so that they were not split in the front like the original pattern. I also spaced them so that they were not in the seams of the sweater and the sleeves. I patterned the neckband so that the design did not go into the buttonhole. There is only one buttonhole in the band at the neck. The yarn I used was Diamonte in Wedgwood Blue and Cream.

Now I am going to tell you that I absolutely love my E6000 BUT ….now I don’t feel like a traitor to Brother machines. This would have been a breeze on the Brother. The only reason I used the Passap was to try fair isle and I won’t do it again. 🙂  EVER!  It is very confusing doing patterns since you have four rows to knit for one row. I also had to keep raising pushers on the ends when I knitted the second color. (like the end needle selection that Brother has). Wrapping was out of the question .

And FLOATS? OMG they are huge. I had to latch tool up behind the flowers to pull the floats in so that there were no gaps between the background and the pattern. I don’t see how that can be avoided using any machine with this pattern though. Well, unless it was knitted in double  jacquard.

I sort of like the jacket better but short items don’t look good on me. I do have to say that this is one of the best fitting sweaters I have ever made and it feels good on me. The sleeves are my perfect length also.

So if a Passap is the only machine you have, this can be done.